Matches in DBpedia 2016-04 for { <http://dbpedia.org/resource/Snap_gage> ?p ?o }
Showing triples 1 to 36 of
36
with 100 triples per page.
- Snap_gage abstract "A snap gage is a form of Go/no go gauge. It is a limit gage with permanently or temporarily fixed measurement aperture(s) (gaps) which is used to quickly verify whether an outside dimension of a part matches a preset dimension or falls within predefined tolerances. The surfaces which define the edges of the aperture are the anvils, which may be made of separate pieces of hard material such as tungsten carbide for wear resistance. Two apertures are frequently used to provide Go/No-Go testing and are often arranged such that a part being measured can pass through the two apertures in sequence; a part that is within tolerance will pass through the first maximum size limit aperture but will not be able to pass through the minimum size limit aperture. A snap gauge usually has a \"C\" shaped frame with the aperture(s) at the opening of the \"C\". Snap gages may be machined and ground out of a single block of metal or adjustable snap gages, which have movable anvils that may be adjusted over a limited range of sizes, may be used. They may also be of built up construction in which one or more gage blocks or feeler gauges are sandwiched between two anvils. Adjustable snap gages may be reset to compensate for wear or re-tasked for measuring a different dimension and can be purchased off the shelf and set rather than needing to be fabricated from scratch when a new gage is needed. Gauge blocks would typically be used to initially set the width of the measuring aperture(s).A variation is the snap indicator gage, which incorporates a dial indicator or electronic digital indicator as one of the anvils. This indicator displays the deviation from the preset dimension and the indicator may have high and low tolerance limits marked by means of two extra needles, alteration of the dial face, or programming into an electronic indicator. Another variation adds, in addition to the dial or electronic indicator, a micrometer adjustment on the anvil opposite the indicator anvil. This may be referred to as a snap gage or an indicating micrometer and may be quickly preset for short runs of parts.Snap gages facilitate making interchangeable parts. Snap gages have been in existence and referred to by that name since at least 1898. In a manufacturing plant, snap gages would normally be re-calibrated at scheduled intervals. Often, snap gages will be calibrated by skilled workers and used by semi-skilled workers; the snap gage is faster than a micrometer and requires less skill to use correctly.Some vendors who resell a different measuring instrument, bore gauge, muddy the waters by referring to them as snap gages, unlike the manufacturer who uses the correct nomenclature. Unlike a snap gage, these measure inside (bore) dimensions, not outside dimensions, and are usually reset for each part measured.".
- Snap_gage thumbnail Snap_gages.jpg?width=300.
- Snap_gage wikiPageID "5904095".
- Snap_gage wikiPageLength "5541".
- Snap_gage wikiPageOutDegree "12".
- Snap_gage wikiPageRevisionID "675779595".
- Snap_gage wikiPageWikiLink Bore_gauge.
- Snap_gage wikiPageWikiLink Category:Length,_distance,_or_range_measuring_devices.
- Snap_gage wikiPageWikiLink Category:Metalworking_measuring_instruments.
- Snap_gage wikiPageWikiLink Feeler_gauge.
- Snap_gage wikiPageWikiLink Gauge_(instrument).
- Snap_gage wikiPageWikiLink Gauge_block.
- Snap_gage wikiPageWikiLink no_go_gauge.
- Snap_gage wikiPageWikiLink Indicator_(distance_amplifying_instrument).
- Snap_gage wikiPageWikiLink Interchangeable_parts.
- Snap_gage wikiPageWikiLink Micrometer.
- Snap_gage wikiPageWikiLink Tungsten_carbide.
- Snap_gage wikiPageWikiLink File:Snap_gages.jpg.
- Snap_gage wikiPageWikiLinkText "snap gage".
- Snap_gage wikiPageUsesTemplate Template:Metalworking_navbox.
- Snap_gage wikiPageUsesTemplate Template:Reflist.
- Snap_gage wikiPageUsesTemplate Template:Use_dmy_dates.
- Snap_gage subject Category:Length,_distance,_or_range_measuring_devices.
- Snap_gage subject Category:Metalworking_measuring_instruments.
- Snap_gage hypernym Form.
- Snap_gage type Instrument.
- Snap_gage type Instrument.
- Snap_gage type Tool.
- Snap_gage comment "A snap gage is a form of Go/no go gauge. It is a limit gage with permanently or temporarily fixed measurement aperture(s) (gaps) which is used to quickly verify whether an outside dimension of a part matches a preset dimension or falls within predefined tolerances. The surfaces which define the edges of the aperture are the anvils, which may be made of separate pieces of hard material such as tungsten carbide for wear resistance.".
- Snap_gage label "Snap gage".
- Snap_gage sameAs Q7547270.
- Snap_gage sameAs m.09v710p.
- Snap_gage sameAs Q7547270.
- Snap_gage wasDerivedFrom Snap_gage?oldid=675779595.
- Snap_gage depiction Snap_gages.jpg.
- Snap_gage isPrimaryTopicOf Snap_gage.
