Matches in DBpedia 2016-04 for { <http://wikidata.dbpedia.org/resource/Q7919301> ?p ?o }
Showing triples 1 to 17 of
17
with 100 triples per page.
- Q7919301 subject Q8414585.
- Q7919301 abstract "A velocity stack, or air horn, is a trumpet-shaped device of differing lengths which is fitted to the air entry of an engine's intake system, carburetor or fuel injection. It is designed to:Allow smooth and even entry of air at high velocities into the intake tract with the flow stream adhering to the pipe walls known as laminar flow.Modify the dynamic tuning range of the intake tract by functioning as a resonating pipe which can adjust the frequency of pressure pulses based on its length within the tract.File:Velocity stack.GIFModern engines universally have tuned intake tract volumes and associated resonance frequencies, designed to provide higher than atmospheric intake air pressure while the intake valves are open - increasing the density of the trapped air in the combustion chamber (higher compression).Modified engines often have the original air box and associated ducting removed and velocity stacks are installed as accessories.Modern fuel injection systems with a plenum and single air inlet typically incorporate some sort of radiused entrance, designed to improve power, based on air flow increases. Power gains are usually at higher rpm.In amateur and professional racing, aftermarket velocity stacks are often used, as rules allow, and gains in the order of 2% to 4% can be obtained when inlet radii and stack lengths are optimized for that engine.OEM automotive manufacturers have many regulations to adhere to. One of these is noise. A properly tuned intake tract produces a rather audible intake noise under high airflow conditions - that is commonly "untuned" to allow the vehicle to pass EPA and DOT noise regulations.The length of the stack is known to have a direct effect on a particular engine's boosted power range.Most current aftermarket stacks are designed to be run "in" the airbox and a company that does research well will have some applications that have all the same length and some applications that have differing lengths of stacks on different cylinders.It is commonly related that "stand off" (air–fuel mix that gets pushed back out of the port, usually at full throttle / low rpm) is somehow captured by installing a longer intake pipe (stack). but, it is actually that the intake valve is closing too late and the combustion chamber is simply overfilling and blowing back out the intake port, before the intake valve closes. A longer inlet pipe will create a later intake pressure wave that will help keep the air in the chamber until the intake valve closes.File:Velocity stack detail.gifThe acceleration of air flow into a duct is inherently a highly efficient process and the difference between even the crudest radius inlet, and the most aerodynamic shape possible is slight, amounting to no more than a few percent.Template:Unreliable source? The flow coefficient of a perfect entry would be 1.0 while the coefficient for a sharp edged entry would be 0.6 and a re-entrant plain pipe 0.5. In practice these latter types of entry are never used for engine intakes. There is always some attempt to provide some radius at the entry. This means that total engine airflow would not increase by the amount suggested by these figures, which apply only to the entry alone, as the inlet end is never the smallest or most restrictive part of the system. Because the greatest losses to flow occur near the valve seat, actual overall gain from any improvement of the entry flow would be much less.In the real world, on high-rpm IR IC engine, using a minimum amount of inlet radius gives the best wave strength and a power boost of 2% to 4% over a 3000 to 3500 rpm range.Using a larger radius, like 3/4", broadens out the resonant pressure wave rpm range, but the compression boosting pressure wave is greatly diminished and almost unnoticed by the engine. The term air horn is sometimes used for velocity stacks; it is unrelated to the noise maker or signalling air horn.".
- Q7919301 thumbnail Velocity_stack.GIF?width=300.
- Q7919301 wikiPageWikiLink Q1003090.
- Q7919301 wikiPageWikiLink Q165435.
- Q7919301 wikiPageWikiLink Q172858.
- Q7919301 wikiPageWikiLink Q1794809.
- Q7919301 wikiPageWikiLink Q189452.
- Q7919301 wikiPageWikiLink Q308881.
- Q7919301 wikiPageWikiLink Q3224368.
- Q7919301 wikiPageWikiLink Q408118.
- Q7919301 wikiPageWikiLink Q7204574.
- Q7919301 wikiPageWikiLink Q7626653.
- Q7919301 wikiPageWikiLink Q8414585.
- Q7919301 comment "A velocity stack, or air horn, is a trumpet-shaped device of differing lengths which is fitted to the air entry of an engine's intake system, carburetor or fuel injection.".
- Q7919301 label "Velocity stack".
- Q7919301 depiction Velocity_stack.GIF.