Matches in DBpedia 2016-04 for { <http://wikidata.dbpedia.org/resource/Q4422580> ?p ?o }
Showing triples 1 to 43 of
43
with 100 triples per page.
- Q4422580 subject Q6967946.
- Q4422580 subject Q8227613.
- Q4422580 subject Q8481399.
- Q4422580 subject Q8913594.
- Q4422580 abstract "A venturi scrubber is designed to effectively use the energy from the inlet gas stream to atomize the liquid being used to scrub the gas stream. This type of technology is a part of the group of air pollution controls collectively referred to as wet scrubbers.Venturi devices have also been used for over 100 years to measure fluid flow (Venturi tubes derived their name from Giovanni Battista Venturi, an Italian physicist). About 35 years ago, Johnstone (1949) and other researchers found that they could effectively use the venturi configuration to remove particles from gas streams. Figure 1 illustrates the classic venturi configuration.A venturi scrubber consists of three sections: a converging section, a throat section, and a diverging section. The inlet gas stream enters the converging section and, as the area decreases, gas velocity increases (in accordance with the Bernoulli equation). Liquid is introduced either at the throat or at the entrance to the converging section. The inlet gas, forced to move at extremely high velocities in the small throat section, shears the liquid from its walls, producing an enormous number of very tiny droplets. Particle and gas removal occur in the diverging section as the inlet gas stream mixes with the fog of tiny liquid droplets. The inlet stream then exits through the diverging section, where it is forced to slow down. Venturis can be used to collect both particulate and gaseous pollutants, but they are more effective in removing particles than gaseous pollutants. Liquid can be injected at the converging section or at the throat. Figure 2 shows liquid injected at the converging section. Thus, the liquid coats the venturi throat making it very effective for handling hot, dry inlet gas that contains dust. Otherwise, the dust would have a tendency to cake on or abrade a dry throat. These venturis are sometimes referred to as having a wetted approach.Figure 3 shows liquid injected at the venturi throat. Since it is sprayed at or just before the throat, it does not actually coat the throat surface. These throats are susceptible to solids buildup when the throat is dry. They are also susceptible to abrasion by dust particles. These venturis are best used when the inlet stream is cool and moist. These venturis are referred to as having a non-wetted approach.Venturis with round throats (Figures 2 and 3) can handle inlet flows as large as 88,000 m³/h (40,000 cfm) (Brady and Legatski 1977). At inlet flow rates greater than this, achieving uniform liquid distribution is difficult, unless additional weirs or baffles are used.To handle large inlet flows, scrubbers designed with long, narrow, rectangular throats (Figure 4) have been used. Simple venturis have fixed throat areas and cannot be used over a wide range of gas flow rates. Manufacturers have developed other modifications to the basic venturi design to maintain scrubber efficiency by changing the throat area for varying inlet gas rates.Certain types of orifices (throat areas) that create more turbulence than a true venturi were found to be equally efficient for a given unit of energy consumed (McIlvaine Company 1974). Results of these findings led to the development of the annular-orifice, or adjustable-throat, venturi scrubber (Figure 5). The size of the throat area is varied by moving a plunger, or adjustable disk, up or down in the throat, thereby decreasing or increasing the annular opening. Gas flows through the annular opening and atomizes liquid that is sprayed onto the plunger or swirled in from the top.Another adjustable-throat venturi is shown in Figure 6. In this scrubber, the throat area is varied by using a movable plate. A water-wash spray is used to continually wash collected material from the plate.Another modification can be seen in the venturi-rod or rod deck scrubber. By placing a number of pipes parallel to each other, a series of longitudinal venturi openings can be created as shown in Figure 7. The area between adjacent rods is a small venturi throat. Water sprays help prevent solids buildup. The principal atomization of the liquid occurs at the rods, where the high-velocity gas moving through spacings creates the small droplets necessary for fine particle collection. These rods must be made of abrasion-resistant material due to the high velocities present.All venturi scrubbers require an entrainment separator because the high velocity of gas through the scrubber will have a tendency to entrain the droplets with the outlet clean gas stream.Cyclonic, mesh-pad, and blade separators are all used to remove liquid droplets from the flue gas and return the liquid to the scrubber water. Cyclonic separators, the most popular for use with venturi scrubbers, are connected to the venturi vessel by a flooded elbow (Figure 8). The liquid reduces abrasion of the elbow as the outlet gas flows at high velocities from the venturi into the separator.".
- Q4422580 thumbnail Venturiscrubber.jpg?width=300.
- Q4422580 wikiPageExternalLink SI_412C_0-5?OpenDocument.
- Q4422580 wikiPageWikiLink Q1188489.
- Q4422580 wikiPageWikiLink Q1261069.
- Q4422580 wikiPageWikiLink Q131123.
- Q4422580 wikiPageWikiLink Q1439803.
- Q4422580 wikiPageWikiLink Q1501437.
- Q4422580 wikiPageWikiLink Q165632.
- Q4422580 wikiPageWikiLink Q177453.
- Q4422580 wikiPageWikiLink Q181328.
- Q4422580 wikiPageWikiLink Q1949855.
- Q4422580 wikiPageWikiLink Q19829510.
- Q4422580 wikiPageWikiLink Q236139.
- Q4422580 wikiPageWikiLink Q250840.
- Q4422580 wikiPageWikiLink Q2556360.
- Q4422580 wikiPageWikiLink Q3195517.
- Q4422580 wikiPageWikiLink Q332828.
- Q4422580 wikiPageWikiLink Q353428.
- Q4422580 wikiPageWikiLink Q3586220.
- Q4422580 wikiPageWikiLink Q412356.
- Q4422580 wikiPageWikiLink Q460173.
- Q4422580 wikiPageWikiLink Q498957.
- Q4422580 wikiPageWikiLink Q5282.
- Q4422580 wikiPageWikiLink Q5380657.
- Q4422580 wikiPageWikiLink Q633570.
- Q4422580 wikiPageWikiLink Q6557322.
- Q4422580 wikiPageWikiLink Q6967946.
- Q4422580 wikiPageWikiLink Q725699.
- Q4422580 wikiPageWikiLink Q748594.
- Q4422580 wikiPageWikiLink Q751029.
- Q4422580 wikiPageWikiLink Q7990022.
- Q4422580 wikiPageWikiLink Q8227613.
- Q4422580 wikiPageWikiLink Q8481399.
- Q4422580 wikiPageWikiLink Q871335.
- Q4422580 wikiPageWikiLink Q8913594.
- Q4422580 comment "A venturi scrubber is designed to effectively use the energy from the inlet gas stream to atomize the liquid being used to scrub the gas stream. This type of technology is a part of the group of air pollution controls collectively referred to as wet scrubbers.Venturi devices have also been used for over 100 years to measure fluid flow (Venturi tubes derived their name from Giovanni Battista Venturi, an Italian physicist).".
- Q4422580 label "Venturi scrubber".
- Q4422580 depiction Venturiscrubber.jpg.