Matches in DBpedia 2016-04 for { <http://dbpedia.org/resource/Power-up_in_standby> ?p ?o }
Showing triples 1 to 32 of
32
with 100 triples per page.
- Power-up_in_standby abstract "Power-up in standby (PUIS) or power management 2 mode (PM2; Western Digital specific) is a SATA or Parallel ATA (aka PATA) hard disk configuration which prevents the drive from automatic spinup when power is applied. The spinup occurs later by an ATA command, only when the disk is needed, to conserve electric power and to avoid a power consumption peak caused by a simultaneous spin-up of multiple disks.PUIS requires corresponding BIOS support. If PM2 is enabled on the drive but not supported by the BIOS, the drive will not be detected by the system or detected as zero in size. PUIS is typically only supported on RAID controllers.PM2 can usually be enabled by jumpering on the drive but can also be configured by other means (configuration sector) using manufacturer specific tools.ATA Commands for PUIS UsageATA Task File SettingsFeature = 0x06 - Enable PUISFeature = 0x86 - Disable PUISFeature = 0x07 - Spin up drive after power onCommand = 0xEF - Set feature".
- Power-up_in_standby wikiPageExternalLink how-to-enable-and-disable-pm2-%28power-management%29-on-wd-sata-drives.
- Power-up_in_standby wikiPageExternalLink 2579-001037.pdf.
- Power-up_in_standby wikiPageID "18700566".
- Power-up_in_standby wikiPageLength "1670".
- Power-up_in_standby wikiPageOutDegree "9".
- Power-up_in_standby wikiPageRevisionID "676043405".
- Power-up_in_standby wikiPageWikiLink BIOS.
- Power-up_in_standby wikiPageWikiLink Category:Hard_disk_drives.
- Power-up_in_standby wikiPageWikiLink Hard_disk_drive.
- Power-up_in_standby wikiPageWikiLink Parallel_ATA.
- Power-up_in_standby wikiPageWikiLink RAID.
- Power-up_in_standby wikiPageWikiLink Serial_ATA.
- Power-up_in_standby wikiPageWikiLink Western_Digital.
- Power-up_in_standby wikiPageWikiLinkText "Power management 2 mode".
- Power-up_in_standby wikiPageWikiLinkText "Power-up in standby".
- Power-up_in_standby wikiPageWikiLinkText "power-up in standby".
- Power-up_in_standby wikiPageUsesTemplate Template:Compu-storage-stub.
- Power-up_in_standby wikiPageUsesTemplate Template:Dubious.
- Power-up_in_standby wikiPageUsesTemplate Template:Mergeto.
- Power-up_in_standby wikiPageUsesTemplate Template:Redirect.
- Power-up_in_standby subject Category:Hard_disk_drives.
- Power-up_in_standby hypernym SATA.
- Power-up_in_standby type Redirect.
- Power-up_in_standby comment "Power-up in standby (PUIS) or power management 2 mode (PM2; Western Digital specific) is a SATA or Parallel ATA (aka PATA) hard disk configuration which prevents the drive from automatic spinup when power is applied. The spinup occurs later by an ATA command, only when the disk is needed, to conserve electric power and to avoid a power consumption peak caused by a simultaneous spin-up of multiple disks.PUIS requires corresponding BIOS support.".
- Power-up_in_standby label "Power-up in standby".
- Power-up_in_standby sameAs Q7236173.
- Power-up_in_standby sameAs m.04gh8mb.
- Power-up_in_standby sameAs Q7236173.
- Power-up_in_standby sameAs 按需启动.
- Power-up_in_standby wasDerivedFrom Power-up_in_standby?oldid=676043405.
- Power-up_in_standby isPrimaryTopicOf Power-up_in_standby.