Matches in DBpedia 2015-10 for { ?s ?p "Molex connector is the vernacular term for a two-piece pin and socket interconnection, most frequently disk drive connectors. Pioneered by Molex Connector Company, the two-piece design became an early electronic standard. Molex developed and patented the first examples of this connector style in the late 1950s and early 1960s. First used in home appliances, other industries soon began designing it into their products from automobiles to vending machines to mini-computers.In such a connector, cylindrical spring-metal pins fit into cylindrical spring-metal sockets. The pins and sockets are held in a rectangular matrix in a nylon shell. The connector typically has two to 24 contacts and is polarized or keyed to ensure correct orientation. Pins and sockets can be arranged in any combination in a single housing, and each housing can be either male or female.There are three typical pin sizes: 1.57 mm (0.062 in), 2.13 mm (0.084 in), and 2.36 mm (0.093 in). The 1.57 mm pin can carry 5 A of current, while the 2.36 mm can carry 8.5 A. Because the pins have a large contact surface area and fit tightly, these connectors are typically used for power.In October 1963 AMP (now a division of Tyco International) introduced the MATE-N-LOK connector. The AMP connector was similar to the patented Molex connectors but not interchangeable. Both were widely used in the computer industry and the term "Molex Connector" is often used to refer to all nylon plugs and receptacles. The first 5.25 inch floppy disk drive, the Shugart SA400, introduced in August 1976 used the AMP MATE-N-LOK connector part number 350211-1. This connector became the standard for 5.25 inch format peripherals such as hard drives and was used until introduction of SATA drives. In 1983, Molex introduced the 8981 connector that was fully compatible with the AMP MATE-N-LOK connector."@en }
Showing triples 1 to 1 of
1
with 100 triples per page.
- Molex_connector abstract "Molex connector is the vernacular term for a two-piece pin and socket interconnection, most frequently disk drive connectors. Pioneered by Molex Connector Company, the two-piece design became an early electronic standard. Molex developed and patented the first examples of this connector style in the late 1950s and early 1960s. First used in home appliances, other industries soon began designing it into their products from automobiles to vending machines to mini-computers.In such a connector, cylindrical spring-metal pins fit into cylindrical spring-metal sockets. The pins and sockets are held in a rectangular matrix in a nylon shell. The connector typically has two to 24 contacts and is polarized or keyed to ensure correct orientation. Pins and sockets can be arranged in any combination in a single housing, and each housing can be either male or female.There are three typical pin sizes: 1.57 mm (0.062 in), 2.13 mm (0.084 in), and 2.36 mm (0.093 in). The 1.57 mm pin can carry 5 A of current, while the 2.36 mm can carry 8.5 A. Because the pins have a large contact surface area and fit tightly, these connectors are typically used for power.In October 1963 AMP (now a division of Tyco International) introduced the MATE-N-LOK connector. The AMP connector was similar to the patented Molex connectors but not interchangeable. Both were widely used in the computer industry and the term "Molex Connector" is often used to refer to all nylon plugs and receptacles. The first 5.25 inch floppy disk drive, the Shugart SA400, introduced in August 1976 used the AMP MATE-N-LOK connector part number 350211-1. This connector became the standard for 5.25 inch format peripherals such as hard drives and was used until introduction of SATA drives. In 1983, Molex introduced the 8981 connector that was fully compatible with the AMP MATE-N-LOK connector.".